Altec TTP-245 Series Manual do Utilizador Página 1

USER’S MANUALTTP-245C / TTP-343C / TTP-244CE THERMAL TRANSFER / DIRECT THERMAL BAR CODE PRINTER

42.2.3 Rear View 1. Ethernet interface 2. USB interface 3. Centronics interface 4. RS-232C interface 5. Power jack socket 6. Power switch 7. Fan

53. Setup 3.1 Setting Up the Printer 1. Place the printer on a flat, secure surface. 2. Make sure the power switch is off. 3. Connect the printer to

63.2 Open / Close the Top Cover 1. Open the printer top cover by pulling the green tabs located on each side towards the front of the printer, then l

73.3 Loading the Ribbon 1. Open the printer’s top cover by pulling the green top cover open levers located on each side of the printer and lifting th

8 5. Stick the ribbon onto the ribbon rewind paper core. 6. Turn the ribbon rewind gear until the ribbon plastic leader is thoroughly wound and t

9 Loading Path for Ribbon

103.4 Loading the Media 3.4.1 Loading the media 1. Open the printer top cover by pulling the green tabs located on each side towards the front of th

11cover gently. 6. Use “Diagnostic Tool” to set the media sensor type and calibrate the selected sensor. (Start the “Diagnostic tool”  Select the

123.4.2 External Label Roll Mount Installation (Option) 1. Attach an external paper roll mount on the bottom of the printer. 2. Insert a 1” label s

136. Move the media guides to fit the label width by turning the guide adjuster knob. 7. Disengage the top cover support and close the top cover gent

iContents Copyright Declaration...i 1. Introduction ...ii 1.1 Product I

143.4.3 Loading Media in Peel-off Mode (Option) 1. Refer to section 3.4.1 to load the media. 2. Feed the paper, printing side facing up, through the

158. Disengage the top cover support and close the top cover gently. 9. Peeling will automatically start. Press the FEED button to test. Note: P

163.4.4 Loading Media in Cutter Mode (Option) 1. Refer to section 3.4.1 to load the media. 2. Lead the media through the cutter paper opening. 3. Mo

173.5 Diagnostic Tool The Diagnostic Utility is a toolbox that allows users to explore the printer's settings and status; change printer setting

183.5.2 Printer Function (Calibrate sensor, Ethernet setup, RTC setup………) 1. Select the PC interface connected with bar code printer. 2. Click the “

193.6 Install SD Memory Card 1. Open the SD memory card cover. 2. Plug in the SD card on main board. 3. Close the memory card cover.

204. LED and Button Functions This printer has one button and one three-color LED indicator. By indicating the LED with different color and pressing

21 Power on utilities The LED color will be changed as following pattern: LED color Functions Amber Red (5 blinks)Amber(5 bl

224.3.2 Gap/Black Mark Calibration, Self-test and Dump Mode While calibrate the gap/black mark sensor, printer will measure the label length, print

23Self-test Printer will print the printer configuration after gap/black mark sensor calibration. Self-test printout can be used to check if there is

ii4.3.6 Skip AUTO.BAS...25 5. Troubleshooting ...

24 Note: 1. Dump mode requires 4” wide paper width. 2. Turn off / on the power to resume printer for normal printing. 3. Press FEED button to back to

254.3.4 Set Black Mark Sensor as Media Sensor and Calibrate the Black Mark Sensor Please follow the steps as below. 1. Turn off the power switch. 2.

265. Troubleshooting The following guide lists the most common problems that may be encountered when operating this bar code printer. If the printer

275.2 Print Quality Problem Possible Cause Recovery Procedure Check if interface cable is well connected to the interface connector. Re-connect ca

286. Maintenance This session presents the clean tools and methods to maintain your printer. 1. Please use one of following material to clean the

29 Please use 100% Ethenol. DO NOT use medical alcohol, which may damage the printer head.  Regularly clean the print head and supply sensors onc

30Revise History Date Content Editor 2008/8/6 Revise the 3.4.3 section(Loading media in peel-off mode)Camille

31 Headquarters / Factory Taipei Office No. 35, Sec. 2, Ligong 1st Rd., Wujie Town 11F, No. 205, Sec. 3, Be

iCopyright Declaration Information in this subject to change without notice and does not represent a commitment on the part of TSC Auto ID Technology

ii1. Introduction 1.1 Product Introduction Thank you for purchasing TSC bar code printer. Although the printer takes only a small amount of space, i

iiiWARNING HAZARDOUS MOVING PARTS KEEP FINGERS AND OTHER BODY PARTS AWAY CAUTION RISK OF EXPLOSION IF BATTERY IS REPLACED BY AN INCORRECT TYPE. DISP

2. Operations Overview 2.1 Unpacking and Inspection This printer has been specially packaged to withstand damage during shipping. Please carefully

22.2 Printer Overview 2.2.1 Front View 1. Ribbon access cover 2. Top cover open lever 3. Media view window 4. LED indicator 5. Feed button 6. SD

32.2.2 Interior view 1. Ribbon rewind hub 2. Ribbon rewind gear 3. Gap sensor (receiver) 4. Media holder 5. Media holder lock switch 6. Gap sens